Honeywell CT8602C Bedienungsanleitung PDF herunterladen

1 69-0446—2

S. M. • Rev. 3-95 • • ©Honeywell Inc. 1995 • Form Number 69-0446—2

CT8602C

Professional Fuel Saver Thermostat

Application

This thermostat provides energy saving control for a

24 Vac gas, oil, or electric heating or heating/cooling

system with independently controlled fan. System switch

positions include HEAT-OFF-COOL: fan switch positions

include ON-AUTO.

Power is supplied for the device by three AA alkaline

batteries (included in package). This allows the thermostat

to be compatible with all control applications.

Heat and cool anticipation is fixed; no adjustment is

necessary. Cycle rates are adjustable for heating.

The current rating is 1.6A maximum up to 30 Vac.

Recycling Notice

If this control is replacing a control that contains mer-

cury in a sealed tube, do not place your old control in the

trash. Contact your local waste management authority for

instructions regarding recycling and the proper disposal of

your old control.

If you have any questions, call Honeywell Inc. at 1-800-

468-1502.

Installation

WHEN INSTALLING THIS PRODUCT…

1. Read these instructions carefully. Failure to follow

them could damage the product or cause a hazardous

condition.

2. Check the ratings given on the product to make sure

the product is suitable for your application.

3. After installation is complete, check out product

operation as provided in these instructions.

4. Allow thermostat to warm to room temperature

before operating.

CAUTION

Disconnect power supply to prevent electrical

shock or equipment damage.

IMPORTANT: Push excess wire back into the hole, and

plug the hole with non hardening caulk, putty or

insulation to prevent drafts from affecting thermo-

stat operation.

LOCATION

Install thermostat and wallplate about 5 ft. (1.5m)

above the floor in an area with good air circulation at

room temperature.

Do not install the thermostat where it may be affected by:

— drafts or dead spots behind doors, in corners, or under

cabinets.

— hot or cold air from ducts.

— radiant heat from sun or appliances.

— concealed pipes and chimneys.

— unheated (uncooled) areas such as an outside wall,

behind the thermostat.

IF REPLACING AN EXISTING THERMOSTAT

Turn off power to thermostat at furnace or boiler. A two-

transformer system may require turning off two switches or

disconnects. Remove any existing wallplate or subbase

from wall. To avoid miswiring later, label or write down

each wire with the letter or number on the wiring terminal

as the wire is removed.

IF NEW INSTALLATION

Run cable to the hole in the selected wall location, and

pull about 3 in. (76 mm) of wire through the opening.

Color-coded, 18 gauge thermostat cable with at least one

conductor for each wiring terminal is recommended.

MOUNTING WALLPLATE

Remove thermostat from wallplate (Fig. 1).

The wallplate does not require leveling for operation,

but only for appearance. The wallplate mounts directly

onto the wall with the screws included in the package. Use

the wallplate as a template, and with a pencil, mark two

mounting screw positions that best fit the application using

two of the three mounting holes in the wallplate (Fig. 2).

Use 3/16 in. bit to drill holes for anchors. Gently tap

anchors into holes until flush with the wall surface. Thread

wires through the center opening of the wallplate. Then

mount the wallplate using the two screws provided. Gently

tighten screws, level top surface of wallplate, and securely

tighten the screws.

Fig. 1—Removing thermostat from wallplate.

M3375

M8850

1 2 3 4 5 6

Inhaltsverzeichnis

Seite 1 - Installation

1 69-0446—2S. M. • Rev. 3-95 • • ©Honeywell Inc. 1995 • Form Number 69-0446—2CT8602C Professional Fuel Saver ThermostatApplicationThis

Seite 2 - CROSS-SECTIONAL VIEW OF

69-0446—2 2Fig. 2—Mounting wallplate on wall. Fig. 4—CT8602C heating-only circuit in acontinuous pilot gas system.Fig. 6—CT8602C heating/cooling circu

Seite 3 - Setting and Adjustments

3 69-0446—2Fig. 7—CT8602C heating/cooling circuit in a twotransformer (one for heating, one for cooling)system with gas heat and electric cooling, RCa

Seite 4 - Fig. 11—Battery placement

69-0446—2 4batteries within approximately 30 seconds from the timethe batteries are removed to prevent program loss andreprogramming.IMPORTANT: The lo

Seite 5

5 69-0446—2FANMove the system switch to OFF, and the fan switch toON. The fan should run continuously. When the fan switchis in the AUTO position, the

Seite 6 - DAY/TIME

69-0446—2 6▲▲▲▲QUALITY IS KEYHome and Building Control Home and Building Control Helping You Control Your WorldHoneywell Inc. Honeywell Limited—Honeyw

Kommentare zu diesen Handbüchern

Keine Kommentare

Honeywell CT8602C Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Schalttafel Honeywell CT8602C herunter. Honeywell CT8602C User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Schalttafel Honeywell CT8602C