INSTALLATION INSTRUCTIONSPut Bar Code Here95-7776-03CE AND OTHER LOGOSWEB-700WEB-700-OCP-700 APPLICATIONThe WEB-700 and CP-700 are compact, embedded
WEB-700 WEB-700-O CP-70095-7776—03 10Board LayoutFig. 5 shows the location of connectors, option slots, and other features of the main board in the WE
WEB-700 WEB-700-O CP-70011 95-7776—03ABOUT EXPANSION OPTIONSThe WEB/CP-700 provides for field-installable expansion using these types of options:• Opt
WEB-700 WEB-700-O CP-70095-7776—03 12OPTION CARD COM PORT ASSIGNMENTSCOM port assignments for option cards installed in a WEB/CP-700 start at COM5, wi
WEB-700 WEB-700-O CP-70013 95-7776—03WIRING DETAILSSee Fig. 5, page 10 to locate connectors and other components on the WEB/CP-700 controller. Make co
WEB-700 WEB-700-O CP-70095-7776—03 14SERIALThere are two “RS” serial ports on the WEB/CP-700 base board. Each has a UART capable of operation up to 11
WEB-700 WEB-700-O CP-70015 95-7776—03Fig. 7. Grounding and power wiring connections to NPB-PWR-UN-H module.Power WiringThere are two power options for
WEB-700 WEB-700-O CP-70095-7776—03 16Wiring NPB-PWR-UN-H input power and earth ground.1. Remove power from the AC circuit being wired to the NPB-PWR-U
WEB-700 WEB-700-O CP-70017 95-7776—03Contact InputsThree contact inputs (CIs) are available on a 6-position connector next to the 2-position external
WEB-700 WEB-700-O CP-70095-7776—03 18EXTERNAL 12V BACKUP BATTERYA 2-position connector provides support for an external 12V sealed lead-acid (SLA) typ
WEB-700 WEB-700-O CP-70019 95-7776—03Wiring to Remote I/O ModulesWiring to remote I/O modules typically provides both 15Vdc power and 12V battery back
WEB-700 WEB-700-O CP-70095-7776—03 2ABOUT THIS GUIDEThis document covers the mounting and wiring of the Tridium® WEB/CP-700 (T-700) controller. It ass
WEB-700 WEB-700-O CP-70095-7776—03 20If after applying power, the STATUS LED goes out, or if the BEAT LED comes on (steady) and stays lit longer than
WEB-700 WEB-700-O CP-70021 95-7776—03ABOUT LEDSThe WEB/CP-700 provides a number of LEDs on its main board. Only the Status and Heartbeat LEDs are visi
WEB-700 WEB-700-O CP-70095-7776—03 22Required NiMH Battery MaintenanceBattery life expectancy is a function of its discharge cycles (the number of dis
WEB-700 WEB-700-O CP-70023 95-7776—03NOTE: Dispose of the used NiMH battery properly. 4. Unplug the NiMH battery from the main board connector (see Fi
WEB-700 WEB-700-O CP-70095-7776—03 24Replacing the WEB/CP-700NOTE: Before handling circuit boards, discharge any accumulated static by touching a near
WEB-700 WEB-700-O CP-70025 95-7776—03Returning a Defective UnitFor proper credit on an in-warranty unit, ship the defective unit to Tridium within 30
WEB-700 WEB-700-O CP-70095-7776—03 26CERTIFICATIONSFederal Communications Commission (FCC)This equipment generates, uses, and can radiate radio freque
WEB-700 WEB-700-O CP-70027 95-7776—03TAB MOUNTING DIMENSIONSMeasurements are in inches and (mm). DIN mounting is recommended over tab mounting. See Fi
WEB-700 WEB-700-O CP-700Automation and Control SolutionsHoneywell International Inc.1985 Douglas Drive NorthGolden Valley, MN 55422customer.honeywell
WEB-700 WEB-700-O CP-7003 95-7776—03PRODUCT DESCRIPTIONThe WEB/CP-700 controller is a compact embedded processor platform using on-board Flash memory
WEB-700 WEB-700-O CP-70095-7776—03 4.Fig. 2. WEB/CP-700 main controller board and 2 option cards uninstalled. As a 7 series controller, the WEB/CP-700
WEB-700 WEB-700-O CP-7005 95-7776—03Technical SpecificationsWEB/CP-700 PLATFORM• PowerPC 440Epx @ 667MHz processor (speed approximate due to spread sp
WEB-700 WEB-700-O CP-70095-7776—03 6PREPARATIONUnpack the WEB/CP-700 and inspect the package contents for damaged or missing components. If damaged, n
WEB-700 WEB-700-O CP-7007 95-7776—03WARNINGA 120Vac or 240Vac circuit powers the NPB-PWR-UN-H power supply for the controller. 15Vdc input (DC only) t
WEB-700 WEB-700-O CP-70095-7776—03 8Physical MountingThe following information applies about physically mounting the unit.• You can mount the WEB/CP-7
WEB-700 WEB-700-O CP-7009 95-7776—03To mount on DIN rail1. Securely install the DIN rail with at least two screws, near the two rail ends.2. Position
Kommentare zu diesen Handbüchern