Honeywell CHRONOTHERM T8611G Bedienungsanleitung PDF herunterladen

® U.S. Registered Trademark

INSTALLATION INSTRUCTIONS

69-1414-2

T8611G Chronotherm

Deluxe Zoning

Heat Pump Thermostat

APPLICATION

The T8611G Chronotherm® Deluxe Zoning Heat Pump Thermostat provides electronic control of 24 Vac zoned heat

pump systems. Refer to Table 1 and Table 2 for a general description of the thermostat and zoning applications.

Table 1. Description of T8611 Thermostats.

Table 2. T8611 Zoning Applications.

MERCURY NOTICE

If this control is replacing a control that contains

mercury in a sealed tube, do not place your old

control in the trash. Dispose of properly.

Contact your local waste management authority

for instructions regarding recycling and the

proper disposal of the old control.

INSTALLATION

When Installing this Product...

1. Read these instructions carefully. Failure to follow

the instructions can damage the product or cause

a hazardous condition.

2. Check the ratings given in the instructions and on

the product to make sure the product is suitable for

your application.

3. Installer must be a trained, experienced service

technician.

4. After completing installation, use these instructions

to check out the product operation.

Location

Install the thermostat about 1.5m (5 ft) above the floor in

an area with good air circulation at average temperature.

See Fig. 1.

Do not install the thermostat where it can be affected by:

— drafts, or dead spots behind doors and in corners.

— hot or cold air from ducts.

— radiant heat from sun or appliances.

— concealed pipes and chimneys.

— unheated (uncooled) areas such as an outside wall

behind the thermostat.

Wallplate Installation

The thermostat can be mounted horizontally on the wall

or on a 2 in. x 4 in. (50.8 mm x 101.6 mm) wiring box.

Position wallplate horizontally on the wall or on a

2 in. x 4 in. (50.8 mm x 101.6 mm) wiring box.

1. Position and level the wallplate (for appearance

only). The thermostat functions correctly even

when not level.

2. Use a pencil to mark the mounting holes.

See Fig. 2.

Model Power Method Changeover System Selection Fan Selection

T8611G2051 Hardwired Automatic or manual Heat-Off-Cool-Auto-Em. Heat On-Auto

Model TotalZone

EMM-3U EMM-3

T8611G2051 Yes Yes No

1 2 3 4 5 6 ... 11 12

Inhaltsverzeichnis

Seite 1 - Heat Pump Thermostat

Seite 2 - 69-1414—2 2

T8611G CHRONOTHERM® DELUXE ZONING HEAT PUMP THERMOSTAT69-1414—2 10NOTE: Press any key and the displayed numbers will change. Press Time ∇ to go to the

Seite 3 - Mounting Thermostat

T8611G CHRONOTHERM® DELUXE ZONING HEAT PUMP THERMOSTAT11 69-1414—2TROUBLESHOOTING GUIDE (TABLE 7)Table 7. Troubleshooting Guide.Symptom Possible Cause

Seite 4 - SETTINGS

69-1414—2 G.H. Rev. 1-03 www.honeywell.com/yourhomeT8611G CHRONOTHERM® DELUXE ZONING HEAT PUMP THERMOSTATPrinted in U.S.A. on recycled paper cont

Seite 5 - INSTALLER SETUP

T8611G CHRONOTHERM® DELUXE ZONING HEAT PUMP THERMOSTAT69-1414—2 2Fig. 1. Typical location of thermostat.Fig. 2. Mounting the wallplate.3. Remove the w

Seite 6 - 69-1414—2 6

T8611G CHRONOTHERM® DELUXE ZONING HEAT PUMP THERMOSTAT3 69-1414—2Fig. 4. Typical wiring diagram for T8611G on TotalZone® Control Panel.Fig. 5. Correct

Seite 7 - 7 69-1414—2

T8611G CHRONOTHERM® DELUXE ZONING HEAT PUMP THERMOSTAT69-1414—2 4Fig. 7. T8611G key locations and descriptions.Using Thermostat KeysThe thermostat key

Seite 8 - View or Reset Timer Settings

T8611G CHRONOTHERM® DELUXE ZONING HEAT PUMP THERMOSTAT5 69-1414—2INSTALLER SETUPThe Installer Setup is used to customize the thermostat to specific sy

Seite 9 - INSTALLER SELF-TEST

T8611G CHRONOTHERM® DELUXE ZONING HEAT PUMP THERMOSTAT69-1414—2 6Degree temperature display14 0 Temperature is displayed in °F1 Temperature is display

Seite 10 - CHECKOUT

T8611G CHRONOTHERM® DELUXE ZONING HEAT PUMP THERMOSTAT7 69-1414—2IMPORTANTReview the settings to confirm that they match the system. Press Run Program

Seite 11 - 11 69-1414—2

T8611G CHRONOTHERM® DELUXE ZONING HEAT PUMP THERMOSTAT69-1414—2 8Setting Current Day and Time1. Press Set Current Day/Time.NOTE: On initial powerup or

Seite 12 - Printed in U.S.A. on recycled

T8611G CHRONOTHERM® DELUXE ZONING HEAT PUMP THERMOSTAT9 69-1414—2INSTALLER SELF-TESTUse the Installer Self-Test to check the thermostat operation. Ref

Kommentare zu diesen Handbüchern

Keine Kommentare

Honeywell CHRONOTHERM T8611G Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Schalttafel Honeywell CHRONOTHERM T8611G herunter. Honeywell CHRONOTHERM T8611G User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Schalttafel Honeywell CHRONOTHERM T8611G