Honeywell H8908B Humidistat Bedienungsanleitung PDF herunterladen

® U.S. Registered Trademark

INSTALLATION INSTRUCTIONS

69- 1341

H8908B Humidistat

H8908C Dehumidistat

APPLICATION

The H8908B Humidistat and H8908C Dehumidistat

(humidity controllers) provide automatic low voltage

control of humidifiers and dehumidifiers or ventilators,

respectively, in central heating and air conditioning sys-

tems. They have a spst, snap-acting, dust-proof switch

and are designed for wall or surface duct mounting.

INSTALLATION

When Installing this Product...

Read these instructions carefully. Failure to follow

them could damage the product or cause a haz-

ardous condition.

Check the ratings given in the instructions and on

the product to make sure the product is suitable

for your application.

Installer must be a trained, experienced service

technician.

After installation is complete, check out product

operation as provided in these instructions.

CAUTION

Personal Injury Hazard.

Power supply can cause electrical shock.

Disconnect power supply before beginning

installation.

Location and Mounting

The styling of the H8908 is designed to blend with the

latest T8600 family of Honeywell Chronotherm® IV

Deluxe Programmable Thermostats. A mounting tem-

plate is included for mounting the H8908 next to the

T8600. The H8908 can also be mounted at any other

convenient location in the living area or equipment

room. See Fig 1.

NOTE: The H8908 electrical connections are not

shared with the thermostat.

Fig. 1. H8908B Humidistat.

Wall Mounting

IMPORTANT

Mount the control in an area with average

room temperature and average relative

humidity.

The following mounting instructions are for mounting

the H8908 on the wall next to the T8600. When install-

ing the H8908 at another location, modify the procedure

to fit the installation.

Hold the mounting template (included) next to the

T8600. Select the mounting side for the H8908.

The template is reversible for mounting on either

the left or right side of the T8600. See Fig. 2.

Mark the holes for the two mounting screws

(included). Then mark the hole for the low voltage

wiring on the template that corresponds with the

side selected in step 1.

Remove the template and drill the holes.

Run low voltage wiring to the location and pull

about 6 in. (152 mm) of wire through the hole.

Plug the hole with nonflammable insulation to

prevent drafts from affecting the control opera-

tion.

Humidity Control

Régulateur d'humidité

M13371

CASE REMOVAL

SLOT

HOLE FOR WIRING

THE DUCT MOUNTING

INSTALLATIONS

1 2 3 4

Inhaltsverzeichnis

Seite 1 - H8908C Dehumidistat

Seite 2 - Duct Mounting

H8908B HUMIDISTAT H8908C DEHUMIDISTAT69-1341 26.Remove the H8908 case from the base. See Fig. 1.7.Position the base on the wall with the arrow up.8.Us

Seite 3 - 3 69-1341

H8908B HUMIDISTAT H8908C DEHUMIDISTAT3 69-1341WIRINGCAUTIONPersonal Injury Hazard.Power supply can cause electrical shock and injury.Disconnect power

Seite 4 - OPERATION AND CHECKOUT

69-1341 G.H. 10-99 Printed in Taiwan R.O.C. www.honeywell.comHome and Building Control Home and Building ControlHoneywell Inc. Honeywell Limi

Verwandte Modelle: H8908C | H8908C Dehumidistat |

Kommentare zu diesen Handbüchern

Keine Kommentare

Honeywell H8908B Humidistat Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Schalttafel Honeywell H8908B Humidistat herunter. Honeywell H8908B Humidistat User Manual [en] Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: H8908C | H8908C Dehumidistat |

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Schalttafel Honeywell H8908B Humidistat