Honeywell T8011R Bedienungsanleitung PDF herunterladen

X-XX UL

INSTALLATION INSTRUCTIONS

®U.S. Registered Trademark

T8011R

Programmable Heat Pump Thermostat

APPLICATION

The T8011R Heat Pump Thermostat provides 24 Vac

control of a two-stage heating and one-stage cooling heat

pump system with manual changeover from heat to cool.

First stage heating and cooling cycle rates are fixed at 3

cph. Second stage heating cycle rate is selectable at

3, 4, 5, 6, 9 or 12 cph. Temperature indication can be set

for °F or °C.

The T8011R Heat Pump Thermostat is powered directly

from the system transformer. Setpoints are held perma-

nently in memory and retained during power outages.

The T8011R model includes a thermostat, wallplate and

owner’s guide. A 7 3/8 in. (188 mm) x 5 3/4 in. (146 mm)

decorator cover plate (for covering wall marks) is available

separately. Order Honeywell part no. 209649A (taupe) or

part no. 209649B (white).

MERCURY NOTICE

If this control is replacing a control that contains

mercury in a sealed tube, do not place your old

control in the trash. Dispose of it properly.

Contact your local waste management authority for

instructions regarding recycling and the proper

disposal of a control.

INSTALLATION

When Installing this Product…

1. Read these instructions carefully. Failure to follow

them could damage the product or cause a hazard-

ous condition.

2. Check the ratings given in the instructions and on

the product to make sure the product is suitable for

your application.

3. Installer must be a trained, experienced service

technician.

4. After installation is complete, check out product

operation as provided in these instructions.

CAUTION

Hazardous Voltage

Can damage heating/cooling system.

Disconnect power at furnace or main breaker/fuse

box.

Location

Install the thermostat about 5 ft (1.5m) above the floor in

an area with good air circulation at average temperature.

See Fig. 1. Do not install the thermostat where it can be

affected by:

— drafts or dead spots behind doors and in corners.

— hot or cold air from ducts.

— radiant heat from the sun or appliances.

— concealed pipes and chimneys.

— unheated (uncooled) areas such as an outside wall

behind the thermostat.

Mounting Wallplate to Wall

IMPORTANT

Level for appearance only. The thermostat

functions normally even when not level.

Mount wallplate and the T8011R with the screws provided

(see Fig. 2) as follows:

1. Place the wallplate at the desired location on the

wall.

2. Pull the thermostat wire through the wallplate

entrance hole.

3. Fasten the wallplate to the wall using the anchors

and screws provided.

4. After wiring the wallplate, plug the hole with non-

flammable insulation to prevent drafts from affecting

the thermostat; see Wiring section.

Table 1. Description of T8011R Thermostat.

69-1436-1

Model System Changeover System Selection Fan Selection Powering Method

T8011R Heat Pump Manual Cool-Off-Heat-Em. Ht. Auto-On Hardwired

1 2 3 4 5 6

Inhaltsverzeichnis

Seite 1 - MERCURY NOTICE

Seite 2 - IMPORTANT

69-1436–12T8011R PROGRAMMABLE HEAT PUMP THERMOSTAT5 FEET[1.5 METERS]YESNONONOM11338Fig. 1. Typical location of thermostat.Fig. 2. Mounting wallplate t

Seite 3 - 69-1436–1

69-1436–13T8011R PROGRAMMABLE HEAT PUMP THERMOSTATFig. 4. Restrict wiring to shaded area.Fig. 5. T8011R two stage heat, one stage cool wiring diagram

Seite 4 - INSTALLER SETUP

69-1436–14T8011R PROGRAMMABLE HEAT PUMP THERMOSTATMounting Thermostat To Wallplate1. Slide SYSTEM switch to the Off position.2. Engage the tabs at the

Seite 5 - OPERATION

69-1436–15T8011R PROGRAMMABLE HEAT PUMP THERMOSTAT3. Setting Heat Cycle Rate (see Table 2 for cycle rateoptions and equipment).a. Press the ▲ key todi

Seite 6 - CHECKOUT

69-1436–16T8011R PROGRAMMABLE HEAT PUMP THERMOSTATHoneywell Limited-Honeywell Limitée35 Dynamic DriveScarborough, Ontario M1V 4Z969-1436–1 G.H.