Honeywell 9782 Series Bedienungsanleitung Seite 118
- Seite / 148
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Conductivity/Resistivity Analyzer/Controller
9782 Series Conductivity/Resistivity Analyzer/Controller - Operator’s Manual 7/9910-2
ATTENTION
Most of the operations described in this section are performed with the unit off-line (that is, not
connected to the process). However, some of the operations described in this section are
performed with the Analyzer/Controller on-line. Your process may be affected as soon as you
initiate the maintenance function.
ATTENTION
This equipment contains devices that can be damaged by electrostatic discharge (ESD). The
damage incurred may not cause the device to fail completely, but may cause early failure.
Therefore, it is imperative that assemblies containing static sensitive devices be carried in non-
conductive plastic bags. When adjusting or performing any work on such assemblies, grounded
work stations and wrist straps must be used. If soldering irons are used, they must also be
grounded.
A grounded work station is any conductive or metallic surface connected to an earth ground,
such as a water pipe, with a 1/2 to 1 megohm resistor in series with the ground connection. The
purpose of the resistor is to current limit an electrostatic discharge and to prevent any shock
hazard to the operator. The steps indicated above must be followed to prevent damage and/or
degradation, which may be induced by ESD, to static sensitive devices.
- 9782 Series Two Cell 1
- Conductivity/Resistivity 1
- Analyzer/Controller 1
- Operator’s Manual 1
- Earth Connnection 2
- About This Document 3
- Contents 4
- 1. Introduction 15
- 1.2 Features 17
- +RQH\ZHOO 19
- 1.3.1 Keypad Use 20
- 1.3.2 Online Displays 22
- C1 0.58 µS 23
- C2 0.25 µS 23
- 01: 58:29 24
- 1.4 Menu Hierarchy 25
- [wide range models only] 26
- 1.5 Planning 27
- Selecting a strategy 30
- 2.1 Specifications 33
- 2.1.4 Electrical 34
- 2.1.5 Model Ranges 34
- 2.1.6 Operating Conditions 35
- 2.1.7 Outputs 36
- 2.1.9 AutoClean 37
- 2.1.10 Control 37
- (9782C-S0 only) 38
- 2.2 Model Number Breakdown 39
- 3.1 Overview 43
- 3.2 Unpacking and Preparing 44
- 3.3 Mounting 45
- Case Outline 46
- Panel Cutout 46
- 4. Power Wiring 51
- ) wire for ac power 53
- Section 2 53
- 4.4 Installing Power Wiring 54
- PE = Protective 55
- Earth Ground 55
- 5.1 Overview 57
- Ease of configuration 58
- Purpose of I/O setup 58
- Illustrations 59
- System defaults 59
- 5.3 Performing I/O Setup 60
- RELAY ACTIVATION 63
- STATE ON ALARM 63
- SELECT DE-ENERGIZE 63
- DISPLAY RESOLUTION 64
- RESOLUTION LOW 64
- UOM uS 64
- I/O SETUP COMPLETE 65
- PRESS 65
- ENTER TO CONTINUE 65
- 65
- CAT/RETRANSMISSION 66
- Cell Cell12− 68
- DISCRETE CONTROL 69
- CYCLE TMR 1 69
- 5.6 Configuring Alarms 72
- ADVANCED FEATURES 73
- 5.8 Configuring AutoClean 74
- COMPUTED VALUE 78
- SELECT DIFFERENCE 78
- 78
- 9782C-S0 79
- 9782C-W0 79
- 6. Input and Output Wiring 83
- Input and Output Wiring 85
- 6.4 Wiring Relays 89
- (simulated 92
- 7.1 Overview 95
- Rinse sequence 96
- Automatic Wash Setup 97
- AutoClean Operation 97
- 8. Calibration 99
- ATTENTION 101
- Calibration 103
- CAL TRIM 1 104
- REMOVE CAL TRIM C1 105
- Introduction 106
- TDS CVSN FACTOR C1 107
- TDS CVSN FACTOR C2 107
- 9. Diagnostics and Messages 109
- 9.2 System Status Messages 110
- 9.3 Process Alarm Messages 111
- Output affected by error 112
- 9.5 Off-Line Diagnostics 113
- KEYBOARD TEST 114
- 9.5.2 Output Tests 115
- OFFLINE FUNCTIONS 116
- OUTPUT/RELAY TEST 116
- 10. Maintenance 117
- 10.2 Output Calibration 119
- MAINTENANCE 120
- INSTRUMENT SETUP 120
- LEAD RESISTANCE COMP 120
- DIAGNOSTICS 120
- 120
- OUTPUT CALIBRATION 121
- MENU TO EXIT 121
- 121
- UPDATE TAG DATA 122
- HONEYWELL INC 122
- 122
- Stored in Memory 123
- FACTORY PASSWORD 124
- 124
- ENTER PASSWORD 124
- SCREEN CONTRAST 125
- Settings 127
- MAINTENANCE 129
- 10.9 Replacing the Fuse 130
- Maintenance 131
- 11.1 Overview 133
- 11.2 Part Numbers 134
- Appendix A 137
- Proportional Control Tuning 137
- Appendix B 139
- Two-Cell Applications 139
- Parts Rinsing 140
- Softener Monitoring 141
- Steam Power Measurements 141
- Appendix C 143
- Appendix D 145
- Honeywell, Inc 148
- 1100 Virginia Drive 148
Verwandte Produkte und Handbücher für Hardware Honeywell 9782 Series
(243 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.157 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern